Introduction

这个作业属于硬件作业了，要求阅读芯片手册，然后写一个时钟驱动。难度的话其实比不过同期的软件作业难度，已经提供了大部分的代码，不过硬件调试需要一定的功底。

I. OBJECTIVES

The purpose of this assignment is to build a package of timing routines for the SAPC and use it to time code on the SAPC to determine memory access time on the SAPC with and without caching. This code does not run on UNIX. Read the Intel 8254 Programmable Interval Timer (PIT) Data Sheet. Look at $pcex/timer.c for an example of C code for accessing the timer. Copy all the files needed for this project.

II. The timing package

A package is a set of utilities that can be called by a program that wants to use them. When designing a package we carefully consider the things in it that must be visible to the caller, specify those, and require that everything else be internal and invisible. The visible parts of the timing package you will build are in timepack.h. A customer for the packages services includes that header file (using #include) in the program for compilation and links his or her object code with timepack_sapc.opc to build the executable. You are asked to modify timepack_sapc.c to provide a high resolution timer service for programs running on the SAPC.

Existing Code

Every package should have a test program showing that it works by calling it in all important ways. This test program is called a driver because it sits on top of the package and drives it like we test-drive a car start up, do this, do that, stop, shut down. It is also called a unit test program because it tests just this one package separate from any other package in a bigger program. If you suspect something is wrong in a certain package, youll try to make its unit test fail, and then you debug the problem in the relatively simple environment of the unit test, rather than in the bigger program. The test program for timepack is testpack.c. You can build testpack and testpack.lnx right away and run them. Note what is printed out by testpack.lnx. Capture this in a typescript1 file. It shows that the timing package (as provided) can time things on the SAPC to 55-ms accuracy, but not to the microsecond accuracy we want. The next step is to get your timepack_sapc.c fixed up for the higher resolution and the unit test executable testpack.lnx will show it.

Modifed Code

Youre working directly with the hardware device, the Programmable Interval Timer (PIT) with its interrupt handler. This code has been provided to you in a). The timepack_sapc.c as provided can measure time in timer ticks at an 18.2-Hz (55 ms/tick) standard PC tick rate.To use the PIT to measure higher precision, you make use of downcounts within the timer chip. What you need to do is determine how many counts have downcounted in the timer since the last tick and compute a higher accuracy time. By doing this at both the start and the end of the time interval being measured, you can compute the elapsed time accurate to a few microseconds, a very respectable timer service. Youll need to modify the timepack_sapc.c to achieve this.
Since timer downcounts count down from 64K at the tick, you need to subtract the register value from 65536 to get the number of downcounts since last tick:

number of downcounts since tick = 65536 - observed_count (in register)

Thus the accurate time between A and B is

= 202 clock ticks + (65536  43000) downcounts - (200 clock ticks + (65536  35000) downcounts)= 2 clock ticks  8000 downcounts

where 1 tick = 64 * 1024 downcounts, so this whole thing can be expressed in downcounts, and then converted to usecs.
Note that you need to convert downcounts (an int) to usecs (another int). To do this, cast the downcount value to double, multiply by the correct double conversion factor, and then cast back to int usecs. The idea here is that the conversion factor is itself non-integral, so the needed multiplication by it needs to be in floating point, resulting in a floating point number accurate to about 1 usec, so we might as well cast it back to an int value since ints are easier to work with.
See the timer.c in the course directory for a C program that reads the timer downcounts you can take code from this as needed.
Dont leave any printfs in your final code that output during timing runs!! They take a really long time and ruin the data. Save the timing figures in memory and print them out after the stoptimer call.
Any private functions or variables you need should be declared static in timepack_sapc.c, so that the calling program can never accidentally use a variable or function with the same name, or interfere with yours. Capture your improved result in a typescript2 file.

III. Timing i486 instructions and a C loop

In this part of the assignment you will use the timing package to time x86 instructions. Instruction execution time is measured in system clock cycles, here 2.5 nsecs for our 400Mhz Pentium systems. The PC timer 0 is accurate only in the usec (microsecond) range so you will need to loop many times and divide by the loop count to get the accuracy needed.
The actual instructions to be timed appear in loops in itests.s, which is an x86 assembler source. These are called from itimes.c.

• Finish itests.s, so that the third instruction to be timed (immediate move of IDATA to register) is properly implemented. Add a fourth instruction of your choice itests.s and itimes.c
• You can use the provided makefile to build an optimized version of the SAPC executable file. The provided makefile has the following definitions:

1
2
3
4
5
6
7
8

# development build: -g provides debugging support, slows down execution
# Use -O2 optimization, no -g on final timing runs!
PC_CFLAGS_DEV = -g -Wall -Wno-implicit -Wshadow -I$(PC_INC) -I$(TIMING)
PC_CFLAGS_OPT = -O2 -Wall -Wno-implicit -Wshadow -I$(PC_INC) -I$(TIMING)
# make default PC_CFLAGS be PC_CFLAGS_DEV
O = DEV
# allow user to override DEV via O=OPT on the command line
PC_CFLAGS = $(PC_CFLAGS_$(O))

You can use O=OPT on the make command line to build an optimized version of the sapc executables. Note that you need to make clean between a development build and an optimized build to get rid of object files. Note that we are turning off debugging when we turn on optimizations. Although gcc allows both at once, debugging with optimizations on can be confusing, and debugging support slows down execution.
Do your final timing runs with the optimized version, except for the C test this should be done both ways to see the effect of development vs. production compiling.

• Look at the itests code in memory using the i386-gdb x/i command. Use disas itests.opc (at the UNIX prompt, using the disas alias from the ulab module) to see addresses of individual instructions. From this information figure out how many bytes there are per tested instruction. Then convert bytes to quadwords(64 bits) to see how many 64-bit reads are involved in instruction fetches. Allow fractional reads, for example .25 or .625 because the CPU does 64-bit reads and then saves unused instruction parts, even with caching off, for use as the next instruction. Add on memory reads or writes needed for the operands to find the total number of reads and writes for each tested instruction. For these operand accesses, the CPU does not save the extra bytes, so even a byte operand access counts as a full 64-bit read or write. Fill in the blanks on the form itimes.txt.
• Use your modified itimes.c and itests.s to time movl %eax,%edx, movl , %eax, movl $MEMADDR, %eax and one other instruction of your choice on a SAPC. Use several values of loopcount and the same value several times to see if the time per instruction is consistent. When you get decent repeatability, fill in the form itimes.txt memory access time estimation. Add your discussion to your copy of the form.

NOTE: Even on the fairly well-defined environment of the SAPC, there are sneaky mechanisms that disturb picture-perfect timing results, so dont despair if your data doesnt follow theory exactly report what you found and discuss it.

Files in this directory:

mp3.txt     the assignment, link this or just print itmakefile    copy this, read for build instructionsitests.s    assembler code for loops to be timed -- you copy, edititimes.c    source code for instruction timer driver -- you copy, edittimepack_sapc.c SAPC timing package -- copy, edittestpack.c  source code for testpack, timing pkg driver -- copy, use as needed (build with make C=testpack)

You shouldnt need to copy or link these: the makefile knows where they are
$SAPC_TOOLS/timing/timepack.h header file for timing package

timepack_unix.c     unix implementation of timing package primitivestimepack_unix_dbg.o unix object code, debug version, for timepack_unixtimepack_unix_opt.o unix object code, opt. version, for timepack_unix

You should have the following files in your directory:
Sources for the master directory for the group:

timepack_sapc.c:    make sure you comment the code properlyitests.s:           indicating the new testsitimes.c:           clearly indicate any changes you have made

FINAL NOTE

In the event that you are unable to correctly complete this assignment by the due date, do not remove the work you were able to accomplish partial credit is always better than none.